Firmware apc 5m. American Power Conversion (APC) is a leading manufacturer of uninterruptible power supplies (UPS) and surge protection products for end-to-end legendary reliability. APC firmware upgrade Index of pubfirmwareapc Adding Firmware for APC and NetBotz Devices in StruxureWare Data Center Expert. Created by Stanislav Kalianov on Feb 16, 2017 Firmware apc. Here you will find Deliberant (LigoWave) APC series products' firmware release notes (news, fixes 128 stations support added to iPoll for the APC 5 M V2 series and the Propeller 2/5 (radios with 64 MB.
Today’s spec hack will look at the built-in frequency counter on an InfiniiVision 1000 X-Series oscilloscope. You may think that a 100 MHz oscilloscope will only let you see signals up to 100 MHz – but that’s not actually true. Jul 20, 2016 - Much cleverer people hacked the orginal UT390B laser range finder but. Test Arduino sketch for NSCE Laser NOT suitable for UNI-T Laser. Signal (there were photos of this signal at oscilloscope) is analysed.
UT-81B multimeter/oscilloscope • • May 4, 2011 • • from is a scopemeter. It is a multimeter with some basic oscilloscope functions. This multimeter can measure what you expect from a normal multimeter: DC V up to 1000V, AC up to 750V, resistance up to 40Mohm, frequency up to 10MHz, capacitance 100uF, AC/DC current 10A (and of course it has also a diode and continuity test).
The measurement inaccuracy is overall around 1% according to documentation which is pretty acceptable figure. The magic lies in the embedded oscilloscope functionality. When you need more than just multimeter reading, you can press a button and get oscilloscope view. In oscilloscope mode bandwidth for UT81B is 8MHz with 40MS/s giving resolution 100ns/div – 5s/div with 8bit ADC. You can do the oscilloscope measurements with normal multimeter leads (OK for low frequencies) or use adapter for real oscilloscope probe (for accurate measurement of higher frequencies).
Oscilloscope together with the multimeter is pretty ideal tool for the technician for reparations on the spot as well as for other professionals in workshops. Possibility to be powered by batteries turn this instrument in an ideal tool to be used as a mobile meter. LCD monochrome display with 160 x 160 pixels is very easy to read thanks to the back-light function. The “Auto-Set” key allows to work very quickly and easily without too much trouble going through settings menus, although I must say that the automatic range setup is pretty slow (it can take more than 10 seconds for the meter to find appropriate vertical and horizontal range). Fortunately there is the manual mode so you can set the range and timebase yourself if you know in advance what to expect.
Overall, for an 8MHz and 40MS/s scope the performance is very good. Meter is best suited for measuring of larger continuous signals. You can stick it directly to mains power for example without worrying ab out anything.
For very low level signals you can easily see interference on the measurements. Measuring on-off events on the scope screen is a bit hard also. One thing I noticed is that multimeter and oscilloscope seem to use pretty much separate electronics inside the device: multimeter part has pretty limited bandwidth while oscilloscope has high bandwidth. When you are working for example at 50 Hz mains power, scope and multimeter readings show about he same. But when measuring signals at many kHz frequency, scope still shows signal amplitude correctly, but multimeter reading shown on the screen is pretty much off from the right value. So multimeter voltage reading is just for DC and low frequency measurements. When the whole device is battery powered, it is completely floating device, so you can freely measure circuit that are connected to ground or other potential that is not ground, just like any normal multimeter.
When you power the device with batteries the multimeter is completely floating, and you are free to do all types of measurements without worrying any grounding issues (like with normal grounded oscilloscope). One good plus is that you can do oscilloscope measurements also on the current measurement range (measuring current waveforms with traditional scope would need some extra adapters / tricks).
The meter looks great and build quality is good. Case is plastic with a rubber surround.
UT81B is quite a brick, a slightly big for a multimeter. The software running the device is not fast, neither too slow – acceptable, but could be faster. The package includes opto-isolated USB cable, safety probes, safety banana to BNC converter, alligator clips, mains power supply,, CD with software for reading scope data, Uni-T 1 year warranty card and a zippered case.